Dodge Journey won’t start – causes and how to fix it
The most common causes that prevent normal starting operation of your Dodge Journey are a dead key fob battery, a dead 12v battery, corrosion on battery terminals, a bad alternator, and a clogged fuel filter.
1. Weak Battery
The most likely cause of your Journey’s engine not cranking or cranking slowly is a weak or dead 12v battery. If a new car battery was installed, the battery may not have yet reached its full capacity; a test can be done to measure the voltage between the battery poles.
Test 12v battery
The voltage of your Dodge Journey’s battery can be precisely measured with a multimeter; successful testing of the car battery, i.e. checking the voltage, usually yields values between 12 and 13 volts; values above 14 or below 11.5 volts necessitate expert evaluation.
Jump start Dodge Journey
If your Journey vehicle’s battery is dead, you can jump start it with jumper cables and a healthy battery from another vehicle. Connect cables to the positive terminal of your Journey’s dead battery and the negative terminal of the donor vehicle’s battery before attempting to jumpstart it.
2. Corrosion on battery
Corrosion on your car battery’s contacts causes contact loss, which means your engine can no longer start properly. To determine if your Journey’s starting problems are caused by dirty battery contacts, investigate them. If you find white deposits or silvery-green deposits but no other damage, you do not need to replace the battery.
Clean battery corrosion
To clean the battery on your Dodge Journey, you must first remove the pole cables; if the pole clamp is very tight, you can open it with pliers; however, do not touch any other parts of the body if you use metal pliers.
3. Weak key fob battery
If your Journey has a push start/stop button, it’s possible that it won’t start because the battery is only used to send the signal for locking/unlocking; if the key fob battery runs out, the door won’t lock or unlock at the touch of a button.
How to start Dodge Journey with dead key fob battery
If your Dodge Journey has no place to insert a key, try placing your key fob as close to the start/stop button as possible; this will rule out any other issues with the first key, such as water damage.
4. Broken starter motor
A starter is a motor that starts your Journey’s engine and has an average life of 100,000 to 150,000 miles. If the starter fails, it will usually need to be replaced. Symptom: A clicking sound, which is the sound of a bad starter motor.
Temporary fix for starter
If your car’s engine won’t start, hit the starter motor with a stick or metal tool; the parts inside the starter may be stuck together or out of alignment, and it’s a good idea to have it inspected.
5. Defective alternator
Alternators are generators that produce electricity; if your Journey’s alternator fails, it will be unable to produce electricity, and the battery will not charge. Alternators are known to last between 200,000 and 300,000 miles in modern cars.
6. Clogged fuel filter
The engine will not function properly and may not start at all if the filter is dirty; cleaning is not possible; the filter can only be changed as part of a regular oil change.
7. Fuel pump failure
The engine will not start if the fuel pump fails; a defective fuel pump can be replaced in your workshop. If the pump is leaking, a power contact is broken, or a line or pump lever is broken, the fuel pump is usually noticeable before failure.
8. Blown fuse
Check all fuses in the fuse box that are necessary for starting the engine; a blown fuse may be the cause of your Journey’s breakdown in rare cases. The fuse box is under power, so repairs or tests should always be done in a workshop rather than at home.
How do I reset my radio in my Dodge Journey?
Put the key in the ignition and turn it on, then simultaneously press and hold the volume and tune buttons for about 10 seconds. The radio will power off and restart, taking a few minutes to load back up.
Does a 2012 Dodge Journey have two thermostats?
The primary thermostat for the 2.0L diesel and 2.4L gas engines is located in the thermostat housing/coolant inlet on the front of the water plenum, while the secondary thermostat is located in the cylinder head under the water plenum.
How do I fix the Bluetooth in my Dodge Journey?
Pull the Hands Free fuse, and the phone should now connect to the Journey’s Unconnect and bluetooth. If the reset fails, check for software updates or faulty wiring behind the dash.
How do you reset the UConnect on a Dodge Journey?
How To Reset UConnect On A Dodge Journey
- Hold the VOLUME and TUNE buttons together for about 10 seconds or until the screen goes black.
- Wait a few seconds for the screen to load back up.
How do you reset the radio on a 2012 Dodge Journey?
To reset the 2012 Dodge Journey radio, simultaneously press and hold the volume and tune buttons for about 10 seconds, or until the screen goes black, then wait a few seconds for the screen to load back up.
How do you reset the radio on a 2013 Dodge Journey?
To do so, press and hold the START/STOP button for at least 8 seconds, then press and hold the temperature up and temperature down buttons for at least 8 seconds. A menu will appear on the screen, with “Reset Radio” at the bottom of the list. Select it, and the system will reboot.
Why is my Dodge Journey overheating?
While there are a number of reasons why your Dodge Journey is overheating, the most common three are a coolant leak (water pump, radiator, hose, etc. ), a failed radiator fan, or a failed thermostat.
Where is the secondary thermostat located?
The primary thermostat is located on the front of the water plenum in the thermostat housing, and the secondary thermostat is located in the cylinder head under the water plenum; one or both thermostats could be bad.
Why does a Dodge Avenger have two thermostats?
The inlet cooling to the engine is controlled by a double-valve thermostat that mixes a re-circulating sensing flow with the radiator cooling flow in this setup.
Does Dodge Journey 2012 have Bluetooth?
The 2012 Dodge Journey comes standard with a Bluetooth system in the dash that can be used for both phone calls and music streaming to the van. To use it, go to your device’s settings menu and search for the van in the bluetooth settings.
What to do if UConnect is not working?
Remove the battery (if removable u2013 see your phone’s owner’s manual) and perform a hard reset in the phone. Delete the pairing history in your phone and Uconnectu00ae system, which is usually found in the phone’s Bluetoothu00ae settings. Verify you are selecting “Uconnect” in the discovered Bluetooth devices on your phone.
Is there a fuse for UConnect?
It’s 15 amps and located in the fuse box under the hood.
How do I reset my UConnect 12?
RamCares is a non-profit organization that helps people in
- Put your vehicle in accessories mode (ACC or RUN)
- hold down the Phone and voice recognition buttons (or the tuner and volume knob) for thirty seconds
- release the buttons.
- turn off the vehicle.
- open the driver’s side door for thirty seconds (or until the dash illumination goes black)