FAQ: How To Give A 2009 Dodge Journey Oil Change?

How do you change the oil on a 2009 Dodge Journey?

The 2009 Dodge Journey with the 2.4L inline-4 engine (engine code ED3 B) can hold 4.4 quarts of synthetic oil, while the 2016 Dodge Journey requires fully synthetic motor oil with a viscosity of SAE 5W-20.

How many quarts of oil does a 2009 Dodge journey take?

Check the oil level after refilling. Capacity: 5.5 quarts (with filter)

How do you reset the oil change light on a 2009 Dodge Journey?

Dodge Journey 2009-2016: How to Reset Oil Life

  1. Turn the ignition to RUN (second position)
  2. Slowly press the accelerator pedal all the way down three times within 10 seconds.
  3. Turn ignition OFF.
  4. Turn ignition to RUN or start the engine to verify if the oil life has been reset.

How long can a Dodge Journey go without an oil change?

An oil change is one of the most basic and contentious services for your vehicle, and Dodge recommends getting your Dodge Journey oil changed every 7,500 to 10,000 miles.

What kind of oil does a 2009 Dodge Journey use?

5 Quart Mobil 1 High Mileage Synthetic Motor Oil 5W-20

Does a 2009 Dodge Journey take synthetic oil?

The 2009 Dodge Journey uses SAE 5W-20 engine oil, which is a popular synthetic fluid that is designed to improve performance, protect the engine, and provide optimal fuel economy in all weather conditions.

How do you reset the oil change light on a 2020 Dodge Journey?

Reset the u201cOil Change Dueu201d light on your Dodge Journey.

  1. Press the Accelerator pedal all the way down slowly 3 times within a 10 second interval.
  2. Turn the ignition to u201cOFF/LOCKu201c. For push button start models, press the u201cEngine Start/Stopu201d button once without holding the brake pedal.
We recommend reading:  FAQ: How Long Will A Journey To Mars Take?

What does check engine light mean Dodge Journey?

If your Dodge Journey’s check engine light illuminates, it means there’s a problem that needs to be addressed right away, and your Dodge should be transported in as soon as possible. This blinking light usually indicates a severe engine misfire, allowing unburned fuel to leak into the exhaust system.

How do I reset my 2010 Dodge Journey?

Steps to follow:

  1. Turn the ignition to RUN (second position)
  2. press the accelerator pedal all the way down three times in 10 seconds
  3. turn ignition OFF.
  4. Turn the ignition to RUN or start the engine to see if the oil life has been reset.

How much is a tune up for Dodge Journey?

The Dodge Journey tune is expected to cost between $325 and $385, with repair labor costing between $225 and $285 and repair parts costing between $100 and $100.

How often should you change spark plugs Dodge Journey?

If you have a 2.4L engine, replace the spark plugs every three years or 30,000 miles.

How much oil does a V6 Dodge Journey take?

If you have a 2.4L 4Cylinder engine, you’ll need 4. 5 US quarts of 5W-20 Fully Synthetic oil, while the 3.6L V6 can hold up to 5.9 US quarts.

How do you reset the oil change light?

While holding the reset button, turn the ignition back to the ON position and keep an eye on the oil change or maintenance light, which should begin to blink. Allow the light to blink ON and OFF for a few seconds before releasing the reset button and turning the ignition off.

We recommend reading:  Question: How Long Was The Journey From Europe To America?

What kind of oil do I put in my Dodge Journey?

When it’s time to change the oil, Dodge recommends using fully synthetic SAE 5W-20 oil, which comes in two types: conventional and synthetic.

Where is the oil filter on Dodge Journey?

The oil filter is located under the vehicle, towards the front, and right in front of the oil pan on the 2015 Dodge Journey. The oil filter helps to remove contaminants from the engine’s oil that build up over time.

Leave a Reply

Your email address will not be published. Required fields are marked *