Often asked: How To Start Dodge Journey If Push Button Not Working?

Dodge Journey won’t start – causes and how to fix it

The most common causes that prevent normal starting operation of your Dodge Journey are a dead key fob battery, a dead 12v battery, corrosion on battery terminals, a bad alternator, and a clogged fuel filter.

1. Weak Battery

The most likely cause of your Journey’s engine not cranking or cranking slowly is a weak or dead 12v battery. If a new car battery was installed, the battery may not have yet reached its full capacity; a test can be done to measure the voltage between the battery poles.

Test 12v battery

The voltage of your Dodge Journey’s battery can be precisely measured with a multimeter; successful testing of the car battery, i.e. checking the voltage, usually yields values between 12 and 13 volts; values above 14 or below 11.5 volts necessitate expert evaluation.

Jump start Dodge Journey

If your Journey vehicle’s battery is dead, you can jump start it with jumper cables and a healthy battery from another vehicle. Connect cables to the positive terminal of your Journey’s dead battery and the negative terminal of the donor vehicle’s battery before attempting to jumpstart it.

2. Corrosion on battery

Corrosion on your car battery’s contacts causes contact loss, which means your engine can no longer start properly. To determine if your Journey’s starting problems are caused by dirty battery contacts, investigate them. If you find white deposits or silvery-green deposits but no other damage, you do not need to replace the battery.

Clean battery corrosion

To clean the battery on your Dodge Journey, you must first remove the pole cables; if the pole clamp is very tight, you can open it with pliers; however, do not touch any other parts of the body if you use metal pliers.

3. Weak key fob battery

If your Journey has a push start/stop button, it’s possible that it won’t start because the battery is only used to send the signal for locking/unlocking; if the key fob battery runs out, the door won’t lock or unlock at the touch of a button.

We recommend reading:  Quick Answer: How Far Is A Sabbarh Days Journey?

How to start Dodge Journey with dead key fob battery

If your Dodge Journey has no place to insert a key, try placing your key fob as close to the start/stop button as possible; this will rule out any other issues with the first key, such as water damage.

4. Broken starter motor

A starter is a motor that starts your Journey’s engine and has an average life of 100,000 to 150,000 miles. If the starter fails, it will usually need to be replaced. Symptom: A clicking sound, which is the sound of a bad starter motor.

Temporary fix for starter

If your car’s engine won’t start, hit the starter motor with a stick or metal tool; the parts inside the starter may be stuck together or out of alignment, and it’s a good idea to have it inspected.

5. Defective alternator

Alternators are generators that produce electricity; if your Journey’s alternator fails, it will be unable to produce electricity, and the battery will not charge. Alternators are known to last between 200,000 and 300,000 miles in modern cars.

6. Clogged fuel filter

The engine will not function properly and may not start at all if the filter is dirty; cleaning is not possible; the filter can only be changed as part of a regular oil change.

7. Fuel pump failure

The engine will not start if the fuel pump fails; a defective fuel pump can be replaced in your workshop. If the pump is leaking, a power contact is broken, or a line or pump lever is broken, the fuel pump is usually noticeable before failure.

We recommend reading:  FAQ: 2010 Dodge Journey Rear Heater Core Replacement How To Replace?

Why is my Dodge Journey not starting?

Dead key fob battery, dead 12v battery, corrosion on battery terminals, bad alternator, clogged fuel filter, broken starter, blown fuse, empty gas tank, immobilizer error, or any fault in the electrical system are the most common causes that prevent your Journey from starting normally.

Why will my push to start not work?

A weak key fob battery is one of the most common causes of a push button start malfunction; if you suspect this is the case for you, hold the key fob as close to the push button start as possible while turning your vehicle on.

Can you turn your car into a push to start?

The good news is that you can do it; the bad news is that it is more difficult to install one of these systems than it is to install one on a vehicle that still uses a key ignition.

What is wrong with the Dodge Journey?

The brakes, electrical system, and interior accessories issues are the most common complaints among Dodge Journey owners, accounting for 36%, 21%, and 7% of total Dodge Journey problems, respectively. The brakes are the most common complaint.

How do I reset my Dodge Journey remote start?

Turn your key back to the “off” position (or press the start button again) within five seconds of turning on your remote car starter. Repeat the on-off cycle three more timesu2014you’ll do four total.

How long does a Dodge Journey battery last?

Dodge Journey batteries typically last 3-5 years, but this varies depending on weather, battery type, driving habits, and other factors. You can extend the life of your Journey battery by: Cleaning the terminals and posts of corrosion with the appropriate cleaning solution

Is push to start reliable?

If you prefer the added security and convenience of a keyless system, the push button start system is a good option as long as you understand the risks, keep the key on your person when you leave, and know how to use the manual system in the event of a malfunction.

We recommend reading:  Readers ask: How To Change A Battery In A 2013 Dodge Journey?

How do you start a car that won’t start?

If your car won’t start, try the following suggestions.

  1. Try cycling the key.
  2. Try tapping on the battery terminals.
  3. Try smacking the starter.
  4. Try shifting the shifter.
  5. Try swapping relays.
  6. Try smacking the fuel tank.
  7. Try un-flooding a flooded engine.

How do you start an automatic car without a starter?

Follow these steps to push a car with an automatic transmission:

  1. Turn the key in the ignition. Remove the parking brake. Press your foot on the brake pedal. Move the shifter to the u201cNu201d (Neutral) position.

How do I enable accessories with a push button start?

To activate the vehicle’s accessory/battery mode, press the start button once without depressing/pushing the brake. For vehicles not equipped with the smart key system (traditional key), turn the key in the ignition system to the first position to activate the vehicle’s accessory mode.

Can you start a push button car without the fob?

Yes, you can drive a car without a key fob once the engine is started; however, if the vehicle is keyless, you must first press the start button to start the engine, after which your car will detect and authenticate the fob.

Why you should wrap your key fob in aluminum foil?

If your car doesn’t have these extra security features, there are other ways to block your key’s signal that don’t involve wrapping it in tin foil like an old sandwich. After all, tin foil has been shown to dampen but not completely block your key fob’s signal due to the material’s lack of density.

Leave a Reply

Your email address will not be published. Required fields are marked *